Optimization of the Possibility of Dropping Materials on the Flip-over Bridge for Cassava Roots with Lifting Capacity of 60-80 tons

Dinh Tung Nguyen1,
1 Research Institute of Agricultural Machinery, Hanoi, Vietnam

Main Article Content

Abstract

The paper presents the results of a survey on the ability to vent and dropping materials of the lift-over bridge for cassava roots with a lifting capacity of 60-80 tons based on the experimental planning model. The content of the survey on the influence of technological and technical parameters on the ability of venting/dropping materials on cassava trucks when the system of lifting-flip equipment uses transmission and hydraulic control. The research results build regression equations to show the influence relationship between the three basic structural parameters as lifting load, lift angle, distance A. Optimizing multi-objective function with Box Behnken algorithm model, the optimal conditions are as follows: A 5000 (mm), lift angle 39.88 (degree), lifting load 60.000 (kg). Under these conditions, the highest guessing performance is 86,6%, then the objective function achieves the expected value of product clearance 99.9 (%), specific energy consumption 6.9 (kW / h). There is no much difference in the results between the regression model and the experimental results, almost similar.

Article Details

References

[1] Nguyễn Đình Tùng, Đỗ Thị Thanh Xuân, Nghiên cứu lựa chọn kết cấu và xây dựng mạch điều khiển truyền động thủy lực cho hệ thống nâng trút sắn củ tải trọng 30-60 tấn, Tạp chí Khoa học và Công nghệ, Số 18 (2018) 23-29.
[2] Tung Nguyen Dinh, An investigation of lifting and discharging cassava roots system using hydraulic transmission, International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 11, (2018) 297-308.
[3] Bùi Hải Triều, Nguyễn Đình Tùng, Truyền động và điều khiển thủy lực ứng dụng, 45-51, Nhà xuất bản khoa học kỹ thuật, Hà Nội, lần 1 2018.
[4] Phạm Văn Lang, Bạch Quốc Khang, Cơ sở lý thuyết quy hoạch thực nghiệm và ứng dụng trong kỹ thuật nông nghiệp, 8-10, Nhà xuất bản Nông nghiệp, Hà Nội, 1998.
[5] Nguyễn Đình Tùng, Nguyễn Văn Tiến và cs, Nghiên cứu, thiết kế, chế tạo hệ thống cầu nâng-lật xe chở sắn củ có điều khiển, truyền động thủy lực phục vụ cho nhà máy chế biến sắn quy mô 450 ÷ 500 tấn củ/ngày, Đề tài MS 003.18.ĐT.BO/HĐKHCN-2018, Bộ Công Thương.
[6] Nguyễn Đình Tùng, Nghiên cứu phân tích kết cấu hệ thống cầu nâng lật xe chở sắn củ trên mô hình số, Kỷ yếu hội nghị khoa học và công nghệ Toàn quốc về Cơ khí lần thứ V, Trường Đại học công nghiệp Hà Nội (2018) 1085-1091.
[7] Dinh Tung Nguyen, Van Tan Nguyen, Lifting and discharging the cassava roots system for hydraulic transmission, Proc. In The First Internatioal Conference on Fluid Machinery and Automation Systems (ICFMAS 2018), on 27th – 28th October 2018 at Hanoi University of Science and Technology, Hanoi, Vietnam, (2018) 474-479.
[8] Spackman, H., Mathematical analysis of actuator forces in a scissor lift. Naval Command, Control and Ocean Surveillance Center. San Diego, CA 92152-5001, USA, 1994, pp. 3-11.
[9] Columbus Mckinnon, Hydraulic lifting tables-standard and high class solutions, 2012, pp. 4-5. www.cmco.eu/pfaff-silberblau.
[10] C. Nitereka, R. Ostrowski, J. Pawl, Compact roll-off trailer configurations for containerhauling applications. US 2008/0056868 A1, 2008, pp. 3-5