A Solution for Creating the Simulating Load on Connecting-Rod in the Experimental Device for Lubricating Condiction of the Connecting-Rod Big End Bearing
Main Article Content
Abstract
The longevity and reliability of the crankshaft-connecting rod assembly in internal combustion engines depends very much on the lubricated regime. Connecting-rod is an important part of the engine, in which the connecting-rod big end bearing works in severe conditions (heavy load and dynamic, high velocity, high temperature, ...). The calculation research for this type bearing need always be equipped with experimental device to compare the calculated results and the experimental results. This paper presents the load simulation solution corresponding to the engine's operating cycle and the force measurement method applied to connecting-rod (connecting-rod big end) model of photoelastic in the special device for lubricating of the connecting-rod big end bearing. The force acting on the connecting-rod includes two traction/compression and flexion forces. These forces are measured by strain gauges by the installation of bridge sensors.).
Keywords
Connecting-rod, bearing, load diagram, strain gauges, belleville washers
Article Details
References
[1]. Cooke W.L., 1965-1966, “Dynamic Displacement in a Diesel Engine Main Bearing”, Proceeding. Lubrication and Wear Second Convention, Instn. Mech. Engrs., Vol. 23.
[2]. Rosenberg R.C., 1973, “A Method for Determining the Influence of Multigrade oils on Journal Bearing Performance “, SEA TRANS. Paper 730483, Vol. 82.
[3]. Bates T.W., Evans P.G., 1985, “Effect of Oil Rheology on Journal Bearing Performance: Part 1 Instrumentation of the Big-End Bearing of a Fired Engine”, Proc. Of the JSLE International Tribology Conference, 8-10 juillet, Tokyo, Japon, 1985.
[4]. Bates S T.W., Benwell S., Evans P.G., 1987, “Effect of Oil Rheology on Journal Bearing Performance: Part 2 - Oil Film Thickness in the Big-End Bearing of an Operating Engine”, Proc. 4th SAE Int. Pacific Conference on Automotive Engineering, Melbourne, Australia, Paper No. 871272.
[5]. Bates T.W., Benwell S., 1988, “Effect of Oil Rheology on Journal Bearing Performance: Part 3 - Newtonian Oils in the Connecting-Rod Bearing of an Operating Engine”, SAE Paper No. 880679.
[6]. Moreau H., 2001, “Mesures des Epaisseurs du Film d’Huile dans les Paliers de Moteur Automobile et Comparaisons avec les Résultats Théoriques”, Thèse de Doctorat de Université de Poitiers.
[7]. Michaud P., 2004, “Modélisation Thermoélasticohydodynamique Tridimensionnelle des Paliers de Moteurs. Mise en Place d’un Banc d’Essais pour Paliers Sous Conditions Sévères”, Thèse de Doctorat à Université de Poitiers.
[8]. Fatu A., 2005, “Modélisation numérique et expérimentale de la lubrification de palier de moteur soumis à des conditions sévères de fonctionnement”, Thèse de doctorat de l’Université de Poitiers.
[9]. Pierre-Eugene J., 1983, “Contribution à l’Etude de la Déformation Elastique d’un Coussinet de Tête de Bielle en Fonctionnement Hydrodynamique Permanent”, Thèse de Doctorat de l’Université de Poitiers.
[10]. Optasanu V., 2000, “Modélisation Expérimentale et Numérique de la Lubrification des Paliers Compliants sous Chargement Dynamique”, Thèse de Doctorat de l’Université de Poitiers.
[11]. Hoang L.V., 2002, “Modélisation Expérimentale de la Lubrification Thermoélasticohydodynamique des Paliers de Tête de Bielle. Comparaison entre les Résultats Théoriques et Expérimentaux”, Thèse de Doctorat de l’Université de Poitiers.
[12]. Pham Minh Tuấn, Lý thuyết động cơ đốt trong, NXB Khoa học và kỹ thuật, 2012.
[13]. Trần Thanh Hải Tùng, Bài giảng Tính toán thiết kế động cơ đốt trong, Khoa Cơ khí giao thông, Trường Đại Học Bách Khoa Đà Nẵng, 2007.
[2]. Rosenberg R.C., 1973, “A Method for Determining the Influence of Multigrade oils on Journal Bearing Performance “, SEA TRANS. Paper 730483, Vol. 82.
[3]. Bates T.W., Evans P.G., 1985, “Effect of Oil Rheology on Journal Bearing Performance: Part 1 Instrumentation of the Big-End Bearing of a Fired Engine”, Proc. Of the JSLE International Tribology Conference, 8-10 juillet, Tokyo, Japon, 1985.
[4]. Bates S T.W., Benwell S., Evans P.G., 1987, “Effect of Oil Rheology on Journal Bearing Performance: Part 2 - Oil Film Thickness in the Big-End Bearing of an Operating Engine”, Proc. 4th SAE Int. Pacific Conference on Automotive Engineering, Melbourne, Australia, Paper No. 871272.
[5]. Bates T.W., Benwell S., 1988, “Effect of Oil Rheology on Journal Bearing Performance: Part 3 - Newtonian Oils in the Connecting-Rod Bearing of an Operating Engine”, SAE Paper No. 880679.
[6]. Moreau H., 2001, “Mesures des Epaisseurs du Film d’Huile dans les Paliers de Moteur Automobile et Comparaisons avec les Résultats Théoriques”, Thèse de Doctorat de Université de Poitiers.
[7]. Michaud P., 2004, “Modélisation Thermoélasticohydodynamique Tridimensionnelle des Paliers de Moteurs. Mise en Place d’un Banc d’Essais pour Paliers Sous Conditions Sévères”, Thèse de Doctorat à Université de Poitiers.
[8]. Fatu A., 2005, “Modélisation numérique et expérimentale de la lubrification de palier de moteur soumis à des conditions sévères de fonctionnement”, Thèse de doctorat de l’Université de Poitiers.
[9]. Pierre-Eugene J., 1983, “Contribution à l’Etude de la Déformation Elastique d’un Coussinet de Tête de Bielle en Fonctionnement Hydrodynamique Permanent”, Thèse de Doctorat de l’Université de Poitiers.
[10]. Optasanu V., 2000, “Modélisation Expérimentale et Numérique de la Lubrification des Paliers Compliants sous Chargement Dynamique”, Thèse de Doctorat de l’Université de Poitiers.
[11]. Hoang L.V., 2002, “Modélisation Expérimentale de la Lubrification Thermoélasticohydodynamique des Paliers de Tête de Bielle. Comparaison entre les Résultats Théoriques et Expérimentaux”, Thèse de Doctorat de l’Université de Poitiers.
[12]. Pham Minh Tuấn, Lý thuyết động cơ đốt trong, NXB Khoa học và kỹ thuật, 2012.
[13]. Trần Thanh Hải Tùng, Bài giảng Tính toán thiết kế động cơ đốt trong, Khoa Cơ khí giao thông, Trường Đại Học Bách Khoa Đà Nẵng, 2007.