Experimental Study to Verify the Effect of Parameters on the Depth of Osmotic Heating with 9XC Hardened Steel after Laser Assisted
Main Article Content
Abstract
Laser assisted turning (LAT) is using a laser beam to preheat the workpiece before turning [1]. In order to verify the influences of parameters on the depth of osmotic heating after laser heating 9XC hardened alloy steel (62 HRC hardness), various parameters such as: laser power, distance of laser tip to the workpiece, laser position, cutting speed and feed rate had been sellected using Taguchi experimental method. The results shows that the laser power is strongly affect to the depth of osmotic heating of 91,27 % comparing with the others of laser source's parameters. Besides that the effect of cutting parameters on depth of osmotic heating was 95,69 % of cutting speed and 4,31 % of feed rate, respectively. From experimental results, a formula for the surface layer as a function of laser power and cutting speed had also been constructed. Results confirmed that permeability characteristic shows a minor change with increasing of cutting speed, whereas laser power demonstrates a significant effect on permeability characteristic.
Keywords
9XC hardened alloy steel, laser power, cutting speed, feed rate, Taguchi
Article Details
References
[1] William M. Steen and Jyotirmoy Mazumder “Laser Material Processing” Springer London Dordrecht Heidelberg New York, (2010).
[2] Design of Experiments (DOE) Using the Taguchi Approach, www.nutekus.com/DOE_topicOverviews35Pg.pdf
[3] GS.TSKH. Bành Tiến Long, PGS.TS. Trần Thế Lực, PGS.TS. Trần Sỹ Túy “Nguyên lý gia công vật liệu” Nhà xuất bản Khoa học và Kỹ thuật (2001).
[4] GS.TS. Trần Văn Địch chủ biên và các tác giả “Công nghệ chế tạo máy” Nhà xuất bản Khoa học và Kỹ thuật (2006).
[5] Tool Materials, ASM 2005 (2007).
[6] GS.TS. Trần Văn Địch “Các phương pháp xác định độ chính xác gia công” Nhà xuất bản Khoa học và Kỹ thuật (2011).
[7] TS. Nguyễn Doãn Ý “Giáo trình quy hoạch thực nghiệm” Nhà xuất bản Khoa học và Kỹ thuật (20012).
[8] C. Sainte-Catherine, M. Jeandin, D. Kechemair, J. P. Ricaud and L. Sabatier “Study of Dynamic Absorptivity at 10.6 µm (CO2) and 1.06 µm (Nd:YAG) Wavelengths as a Function of Temperature” Journal de Phique IV Colloque, 1991 01 (C7), pp.C7-151-C7-157.
[2] Design of Experiments (DOE) Using the Taguchi Approach, www.nutekus.com/DOE_topicOverviews35Pg.pdf
[3] GS.TSKH. Bành Tiến Long, PGS.TS. Trần Thế Lực, PGS.TS. Trần Sỹ Túy “Nguyên lý gia công vật liệu” Nhà xuất bản Khoa học và Kỹ thuật (2001).
[4] GS.TS. Trần Văn Địch chủ biên và các tác giả “Công nghệ chế tạo máy” Nhà xuất bản Khoa học và Kỹ thuật (2006).
[5] Tool Materials, ASM 2005 (2007).
[6] GS.TS. Trần Văn Địch “Các phương pháp xác định độ chính xác gia công” Nhà xuất bản Khoa học và Kỹ thuật (2011).
[7] TS. Nguyễn Doãn Ý “Giáo trình quy hoạch thực nghiệm” Nhà xuất bản Khoa học và Kỹ thuật (20012).
[8] C. Sainte-Catherine, M. Jeandin, D. Kechemair, J. P. Ricaud and L. Sabatier “Study of Dynamic Absorptivity at 10.6 µm (CO2) and 1.06 µm (Nd:YAG) Wavelengths as a Function of Temperature” Journal de Phique IV Colloque, 1991 01 (C7), pp.C7-151-C7-157.