Factors affecting the flocculation process waste emulsion cutting oil reduce COD content
Main Article Content
Abstract
Waste emulsion cutting oil has a very high COD (Chemical Oxygen Demand) and it was very harmful to the environment. In this study, flocculation method was investigated to reduce COD of the waste emulsion cutting oil discharged from Samsung, Thai-nguyen company. The waste emulsion cutting oil with the initial parameters such as oil content of 5.35%v/v; pH = 8.72; COD = 147,200 mg/l was used. Particle size and its distribution of the emulsion were determined by laser scattering. Results showed that the particle size of the emulsion has a narrow characteristic ranging from 0.058 to 1.729 µm, averaged at 0.22 µm. Several factors affecting to the flocculation process were pH (ranging from 3 to 10); Al2(SO4)3 content; C-PAM content and stirring speed during treatment of emulsion cutting oil. The best efficiency in COD reduction obtained was 98.24% (COD is 2,586 mg/l) at the optimum condition of pH = 5; Al2(SO4)3 of 2 g/l; C-PAM of 12 mg/kg at a stirring speed of 50 rpm for 25 minutes.
Keywords
waste emulsion, flocculation, Al2(SO4)3, C-PAM, COD
Article Details
References
[1]. Eduardo Lima; Metalworking fluids foam control based on novel surfactants technology, Technical Service and Development- Dow Latin America, (2015) 17-21.
[2]. Carlos E.Santo, Victor J.P. Vilar, Cidalia M.S. Botelho, Amit Bhatnagar, Eva Kumar, Rui A.R. Boaventura, Optimization of coagulation–flocculation and flotation parameters for the treatment of a petroleum refinery effluent from a Portuguese plant, Chemical Engineering Journal 183 (2012) 117–123.
[3]. María Matos, Carlos F. García, Miguel A. Suárez, Carmen Pazos, José M. Benito,Treatment of oil-inwater emulsions by a destabilization/ultrafiltration hybrid process: Statistical analysis of operating parameters, Journal of the Taiwan Institute of Chemical Engineers 59 (2016) 295–302.
[4]. Mohammad Mehdi Amina, Mohammad Mehdi Golbini Mofrad, Hamidreza Pourzamani, Seyed Mohammad Sebaradara, Karim Ebrahim, Treatment of industrial wastewater contaminated with recalcitrant metal working fluids by the photo-Fenton process as post-treatment for DAF, Journal of Industrial and Engineering Chemistry 45 (2017) 412–420.
[5]. Abdullah Almojjlya, Daniel Johnsona, Darren L. Oatley-Radcliffea, Nidal Hilal, Removal of oil from oil-water emulsion by hybrid coagulation/sand filter aspre-treatment, Journal of Water Process Engineering 26 (2018) 17-27.
[6]. R. Etchepare, H. Oliveira, A. Azevedo, J. Rubio, Separation of emulsified crude oil in saline water by dissolved air flotation with micro and nanobubbles, Separation and Purification Technology 186 (2017) 326–332.
[7]. P. Painmanakul, T. Chintateerachai, S. Lertlapwasin, N. Rojvilavan, T. Chalermsinsuwan, N. Chawaloesphonsiya, O. Larpparisudthi, Treatment of Cutting Oily - Wastewater by Sono Fenton Process: Experimental Approach and Combined Process, International Scholarly and Scientific Research & Innovation 7(12) (2013) 936-940.
[8]. Chunjian Su, Gaohua Cao, Shumei Lou, Rui Wang, Fengru Yuan, Longyun Yang & Qing Wang, reatment of Cutting Fluid Waste using Activated Carbon Fiber Supported Nanometer Iron as a Heterogeneous Fenton Catalyst, Scientific reports (2018) 8:10650. https://doi.org/10.1038/s41598-018-29014-4.
[9]. Gos report, Global metalworking fluids market research report 2017, May 2017.
[10]. TCVN 6491: 1999 (ISO 6060: 1989), Chất lượng nước- xác định nhu cầu oxy hóa học, (1999).
[11]. O.P. Sahu, P.K. Chaudhari, Review on chemical treament of industrial waste water, Desalination and Water Treatment vol.17 (2) (2013) 241-257.
[12]. QCVN 52:2013/BTNMT quy chuẩn ký thuật quốc gia về nước thải công nghiệp trong sản xuất thép.
[2]. Carlos E.Santo, Victor J.P. Vilar, Cidalia M.S. Botelho, Amit Bhatnagar, Eva Kumar, Rui A.R. Boaventura, Optimization of coagulation–flocculation and flotation parameters for the treatment of a petroleum refinery effluent from a Portuguese plant, Chemical Engineering Journal 183 (2012) 117–123.
[3]. María Matos, Carlos F. García, Miguel A. Suárez, Carmen Pazos, José M. Benito,Treatment of oil-inwater emulsions by a destabilization/ultrafiltration hybrid process: Statistical analysis of operating parameters, Journal of the Taiwan Institute of Chemical Engineers 59 (2016) 295–302.
[4]. Mohammad Mehdi Amina, Mohammad Mehdi Golbini Mofrad, Hamidreza Pourzamani, Seyed Mohammad Sebaradara, Karim Ebrahim, Treatment of industrial wastewater contaminated with recalcitrant metal working fluids by the photo-Fenton process as post-treatment for DAF, Journal of Industrial and Engineering Chemistry 45 (2017) 412–420.
[5]. Abdullah Almojjlya, Daniel Johnsona, Darren L. Oatley-Radcliffea, Nidal Hilal, Removal of oil from oil-water emulsion by hybrid coagulation/sand filter aspre-treatment, Journal of Water Process Engineering 26 (2018) 17-27.
[6]. R. Etchepare, H. Oliveira, A. Azevedo, J. Rubio, Separation of emulsified crude oil in saline water by dissolved air flotation with micro and nanobubbles, Separation and Purification Technology 186 (2017) 326–332.
[7]. P. Painmanakul, T. Chintateerachai, S. Lertlapwasin, N. Rojvilavan, T. Chalermsinsuwan, N. Chawaloesphonsiya, O. Larpparisudthi, Treatment of Cutting Oily - Wastewater by Sono Fenton Process: Experimental Approach and Combined Process, International Scholarly and Scientific Research & Innovation 7(12) (2013) 936-940.
[8]. Chunjian Su, Gaohua Cao, Shumei Lou, Rui Wang, Fengru Yuan, Longyun Yang & Qing Wang, reatment of Cutting Fluid Waste using Activated Carbon Fiber Supported Nanometer Iron as a Heterogeneous Fenton Catalyst, Scientific reports (2018) 8:10650. https://doi.org/10.1038/s41598-018-29014-4.
[9]. Gos report, Global metalworking fluids market research report 2017, May 2017.
[10]. TCVN 6491: 1999 (ISO 6060: 1989), Chất lượng nước- xác định nhu cầu oxy hóa học, (1999).
[11]. O.P. Sahu, P.K. Chaudhari, Review on chemical treament of industrial waste water, Desalination and Water Treatment vol.17 (2) (2013) 241-257.
[12]. QCVN 52:2013/BTNMT quy chuẩn ký thuật quốc gia về nước thải công nghiệp trong sản xuất thép.