Dynamic Analysis of a Two-Degree-Of-Freedom Engine-Chassis System Using a Magnetorheological Mount
Main Article Content
Abstract
This study presents the mathematical modeling and dynamic analysis of a two-degree-of-freedom (2DOF) engine-chassis system utilizing a magnetorheological (MR) mount integrated with a magnetic shield. Based on the Bingham plastic model, numerical simulations were conducted using the ODE45 solver in MATLAB/Simulink to quantitatively evaluate the vibration responses in both the time and frequency domains under varying excitation currents ranging from 0 to 2 A. The results indicate that the MR mount exhibits superior vibration attenuation capabilities; as the applied current increases, the displacement and velocity amplitudes of the engine are significantly reduced, particularly at the two resonance peaks of 1.07 Hz (in-phase) and 3.47 Hz (out-of-phase). However, the study reveals that excitation currents above 1.25 A are counterproductive to overall chassis ride comfort. This performance degradation at high currents is physically governed by the classical damping-transmissibility trade-off at frequencies well above resonance, leading to an observed increase in the chassis response. The optimal operating region is determined to be within the current range of 0 A to 1.0 A, where the acceleration amplitude transmitted to the chassis is maintained at a low level. This research not only solidifies the theoretical foundation for modeling smart mounting systems but also provides essential data for developing semi-active control strategies, thereby promoting the practical application potential of MR mounts in the automotive industry.
Keywords
Magnetorheological mount (MR mount), magnetorheological fluid (MR fluid), two-degree-of-freedom (2DOF), vibration isolation, magnetic saturation.
Article Details

This work is licensed under a Creative Commons Attribution 4.0 International License.
References
[1] J. Fu, C. Huang, R. Shu, X. Quan, M. Chen, Z. Chen, and B. Chen, Multi-objective optimization of magnetorheological mount considering optimal damping force and maximum adjustable coefficient, Machines, vol. 11, no. 1, p. 60, Jan. 2023. https://doi.org/10.3390/machines11010060
[2] W. Lv, K. Chen, W. Li, and M. Dong, A Method for analysing in-vehicle acoustic response to engine excitation, Engineering, vol. 6, no. 11, p. 285, Oct. 2025. https://doi.org/10.3390/eng6110285
[3] Z. Rao, L. Tang, and Y. Shi, Structural design and static stiffness optimization of magnetorheological suspension for automotive engine, Applied Sciences, vol. 14, no. 16, Aug. 2024, Art. no. 6975. https://doi.org/10.3390/app14166975
[4] Q. Liu, G.-D. Bai, Z.-H. Liu, X.-X. F. Bai, H. Du. P. Chen, and L.-J. Qian, Magnetorheological semi-active mount system for engines: prototyping and testing, Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, vol. 234, iss. 13, pp. 3081–3094, Jun. 2020. https://doi.org/10.1177/0954407020925724
[5] S.-Y. Yang, C. Han, S.-U. Shin, and S.-B. Choi, Design and evaluation of a semi-active magneto-rheological mount for a wheel loader cabin, Actuators, vol. 6, no. 2, p. 16, Apr. 2017. https://doi.org/10.3390/act6020016
[6] R. N. Jazar, Vehicle Dynamics: Theory and Application, Cham, Switzerland: Springer Nature, 2025.
[7] H. Q. Tuan and N. M. Dung, Analysis of the damping performance of an automotive seat suspension system using a magnetorheological mount via an integrated simulation approach, HaUI Journal of Science and Technology, vol. 62, no. 6A, pp. 207–213, Jun. 2026, (In Vietnamese: Phân tích hiệu quả giảm chấn của hệ thống treo ghế ô tô bằng gối đỡ từ lưu biến thông qua phương pháp mô phỏng tích hợp). https://doi.org/10.57001/huih5804.2026.168
[8] J. S. Kumar, P. S. Paul, G. Raghunathan, and D. G. Alex, A review of challenges and solutions in the preparation and use of magnetorheological fluids, International Journal of Mechanical and Materials Engineering, vol. 14, no. 1, Nov. 2019, Art. no. 13. https://doi.org/10.1186/s40712-019-0109-2
[9] Z. Deng, Q. Yang, and X. Yang, Optimal design and experimental evaluation of magneto-rheological mount applied to start/stop mode of vehicle powertrain, Journal of Intelligent Material Systems and Structures, vol. 31, iss. 8, pp. 1126–1137, May 2020. https://doi.org/10.1177/1045389X20910271
[10] S.-H. Kim, D.-S. Yoo, G.-W. Kim, S.-B. Choi, J.-Y. Jeong, J.-H. Kim, S.-J. Kim, and I.-D. Kim, Road traveling test for vibration control of a wheel loader cabin installed with magnetorheological mounts, Journal of Intelligent Material Systems and Structures, vol. 32, iss. 12, pp. 1336–1348, Jul. 2021. https://doi.org/10.1177/1045389X20953900
[11] Q. T. Hoang and H. Q. Vu, Parametric study on the magnetic circuit of MR mounts utilizing magnetic shielding, Scientific Journal of Silesian University of Technology. Series Transport, vol. 132, pp. 129–144, 2026. https://doi.org/10.20858/sjsutst.2026.132.7
[12] B. Sapiński and J. J. Snamina, Automotive vehicle engine mount based on an MR squeeze-mode damper: modeling and simulation, Journal of Theoretical and Applied Mechanics, vol. 55, no. 1, pp. 377–388, Jan. 2017.
[13] X. F. Bai, P. Chen, L.-J. Qian, and P. Kan, Design and analysis of a magnetorheological fluid mount featuring uni-directional squeeze mode, in Proceedings of the ASME 2015 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS2015), Colorado Springs, CO, USA, Sep. 2015, Paper No. SMASIS2015-8813.
[14] LORD Corporation, MRF-132DG Magneto-Rheological Fluid,. [Online]. Available: https://www.shoplordmr.com/mr-products/mrf-132dg-magneto-rheological-fluid-1-liter, Accessed on: Jul. 31, 2025.
[15] H. P. Salunkhe, S. Thikane, and S. Sadale, Magnetorheological damper and its applications: current scenario and future prospects, Romanian Journal of Acoustics and Vibration, vol. 20, no. 1, pp. 20–29, Aug. 2023.